• 微型鼓風機使用本公司固有的空氣動壓軸承技術(非接觸型軸承)。主軸和套筒保持在非接觸狀態下,通過旋轉給此間隙的空氣加壓產生絕妙的空氣壓力分布,因此能夠保持固定主軸所需要的足夠壓力。是更小型、輕量化的劃時代新產品。 特征 空氣動壓軸承技術 超小型,超輕量 高靜壓 低振動 壽命長 應用: 醫療器械(如 CPAP ),家用燃料電池系統,打印機(如 3D 打印機)、服務器、離子發生器 等

  • TGS8100 MEMS semiconductor gas sensor Usable in devices previously impractical for gas sensors Smaller, with significantly reduced power consumption. The history of gas sensor development has frequently focused on miniaturization and reduced power consumption. Figaro Engineering has succeeded in development of the TGS8100 MEMS semiconductor gas sensor, boasting a size and power consumption among the lowest in the world which in turn simplify product design and enhance automated manufacturing. World’s smallest gas sensor class(0.99mm×2.5mm×3.2mm) Sensor miniaturization enables further miniaturization of electronic devices and application to mobile terminals and wearable devices. Expanding possibilities for battery drive Low Power consumption At 15mW of constant powering, power consumption is reduced by approximately 92% in comparison to conventional products. While miniaturization may raise concerns about reliability of gas sensors, TGS8100 maintains chemical stability via special MEMS manufacturing techniques combined with Figaro’s extensive expertise in sensor materials. Furthermore, the potential for intermittent drive allows for the possibility of battery operation, permitting use in devices and equipment not previously possible. When intermittently powered, the gas sensor reaches heater ON temperature in just a few seconds, enabling rapid gas detection. While intermittent drive raises concerns over the adverse effects of thermal shock on sensor structure, the unique design of TGS8100 minimizes these effects. Sensor package generates negligible heat Simplifies thermal design of final device While the large heat output of conventional gas sensors causes heating of the sensor’s package surface, the TGS8100 is a negligible heat source when mounted inside a device. Electronic components and actuators in the vicinity of the sensor are therefore unaffected and the design of devices employing temperature and humidity sensors need not consider the sensor’s effect on internal heating, greatly simplifying product design.
  • TGS 5141 - for the detection of Carbon Monoxide Figaro’s TGS5141 is a battery operable electrochemical sensor which uses a unique electrolyte that eliminates the need for a water reservoir. By eliminating the water reservoir used in TGS5042, the comparative size of TGS5141 is reduced to just 10% of TGS5042. With its ultra compact size, this sensor is the ideal choice for size oriented applications such as portable CO detectors, small residential CO detectors, and multi-sensor fire detectors. OEM customers will find individual sensors data printed on each sensor in bar code form, enabling users to skip the costly gas calibration process and allowing for individual sensor tracking. Features: Ultra compact Battery operable High repeatability/selectivity to CO Linear relationship between CO gas concentration and sensor output Simple calibration Long life UL recognized component Meets UL2034, EN50291, and EN54-31 requirements
  • RHB Series Realized higher voltage than RWE series. ( 575 to 700Vdc ) Endurance with ripple current : 2,000 hours at 85 ℃ Suitable for X-ray and welder power supply where high energy is required RoHS Compliant

  • MZR Series Downsizing and Lower ESR, 2,000 hours at 105 Rated voltage range :6.3 to 50V, Nominal capacitance range :22 to 2,200μF Solvent resistant type Vibration resistant structure RoHS Compliant AEC-Q200 compliant : Please contact Weltronics for more details, test data, information
  • KXL Series Ideal for low profile power supply applications Downsizing from KXJ series Rated voltage range : 400 to 450Vdc, Capacitance range : 15 to 150μF Endurance with ripple current : 10,000 to 12,000 hours at 105 ℃ Non solvent resistant type RoHS Compliant
  • MHS S eries Downsizing, High capacitance Endurance : 5,000 hours at 125 ℃ For high temperature and high reliability applications (Base station equipment, etc) High temperature reflow soldering (3 times) Solvent resistant type(see PRECAUTIONS AND GUIDELINES) Vibration resistant structure RoHS Compliant AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information.
  • LTPD247/347 Features: High performance in compact design Label printing Maximum print speed: up to 200 mm / sec Platen latch function Paper width (mm): 58/80 Print speed (mm / sec) max: 200 Operating voltage (Vp): 21.6 to 26.4 Applications: Business cash registers Measuring instruments Barcode Label Medical equipment
  • LTP04 Features: Max printing speed: 250mm/sec Heavy-duty: 150km, 2mil. cuts Easy maintenance:Major parts are replaceable without tools Paper width (mm): 80 Print speed (mm / sec) max: 250 Operating voltage (Vp): 21.6 ~ 26.4 Application: Business cash registers Measuring equipment Gaming
  • LTPF Features: Max printing speed: 220mm/sec Platen latch function Auto cutter option (Slide type) available Paper width (mm): 58/80 Print speed (mm / sec) max: 220 Operating voltage (Vp): 21.6 to 26.4 Application: usiness cash registers Credit card payment Barcode Measuring equipment Klosk system Medical equipment
  • DPU-S Features: Max printing speed:100mm/sec (DPU-S245) 90mm/sec (DPU-S445) Interface: Bluetooth , USB, IrDA and Serial Compact and light-weight Paper width (mm): 58/112 Print speed (mm / sec) max: 100/90 Cut Type: toothed tear bits Easy paper operation Wide variety of driver and utility software suite Application: Handheld Computer Portable Printing Barcode
  • RP-E10 Features: RP-E10 : Receipt top-exit RP-E11 : Receipt front-exit (IPX1) Compact cube : 129mm x 129mm x 129mm Max printing speed : 350mm/sec High Reliability : 150km, 2 million cuts Various drivers Wide variety of driver and utility software suite Large LED indicator (Multi-color)
  • CAPD247/347 Features: Built-in automatic cutter Easy lift design jams Maximum print speed: up to 200 mm / sec Platen axis lock function and easy separation design Paper width (mm): 58 Print speed (mm / sec) max: 200 bull; operating voltage (Vp): 21.6 to 26.4 Application: business cash registers credit card payment measuring equipment Barcode Klosk system
  • LTP01 Features: Maximum print speed: 75 mm / sec Compact and lightweight body Compatible LTPZ245 Paper width (mm): 58 Print speed (mm / sec) max: 75 operating voltage (Vp): 4.75 to 9.5 Application: business cash registers credit card payment measuring equipment Portable Printing Medical equipment
  • LTP02 Features: Maximum print speed: 100 mm / sec most suitable for miniaturization of the mobile terminal Ultra-lightweight: weighs only 28 grams Paper width (mm): 58 Print speed (mm / sec) max: 100 operating voltage (Vp): 5.5 to 9.5 Application: business cash registers credit card payment measuring equipment Portable Printing Medical equipment
  • LTPJ Features: Max. printing speed: 75 mm / sec Compact and light-weight Front open mechanism with latch function Paper width (mm): 58 Print speed (mm / sec) max: 75 Operating voltage (Vp): 5.5 to 9.5 Application: Business cash registers Credit card payment Measuring equipment Portable Printing Medical equipment
  • Features: Maximum print speed: 75 mm / sec Ultra Compact Design Compact and only 30 grams Paper width (mm): 58 Print Speed (mm / sec) max: 75 Operating voltage (Vp): 5.5 to 9.5 Platen axis lock function and easy separation design
  • CAPM Features: Max. printing speed: 300mm/sec Build in auto paper cutter Head open design for easy paper operation Heavy-duty : 200km, 2mil. cuts Wide operating temperature : -20 C to 60 C Paper width (mm): 58 Operating voltage (Vp): 21.6 to 26.4 Cut Type: full cut or half cut (middle left point) Application: business cash registers measuring instrument Barcode Klosk system Receipt Printer Gaming
  • Features: Current detecting resistors for power supply, motor circuits, etc. High reliability and performance with resistance tolerance 0.5%, T.C.R. 100 10-6/K. Suitable for both reflow and flow solderings. Products with lead free termination meet EU-RoHS requirements.EU-RoHS regulation is not intended for Pb-glass contained in electrode, resistor element and glass. AEC-Q200 Qualified(Except 1H). Applications: Computers HDDs, Cellular-telephones Power supplies, and Motor circuits
  • Features: Small 1.2 f cylindrical package photolithographic processing technology excellent impact resistance, heat resistance RoHS compliant products Fully lead-free Nominal frequency: 32.768kHz Frequency tolerance: plusmn;20 x 10 -6 , 30 x 10 -6 , 50 x 10 -6
  • LTPD245/345 Features: Lightweight body and high functionality The maximum print speed (LTPD245): 100 mm / sec Platen axis lock function and easy separation design Label Printing Paper width: 58mm, 80mm Print speed (mm / sec) max: 100/80 Operating voltage (Vp): 4.75 to 9.5 Application: Business cash registers The number of card payments measuring equipment Barcode Portable Printing Label Medical equipment
  • CAPD245/345 Features: With automatic cutter Easy to lift the jam design The maximum print speed (CAPD245): up to 100 mm / sec Platen axis lock function and easy separation design Paper width: 58mm, 80mm Print speed (mm / sec) max: 100/80 Operating voltage (Vp): 4.75 to 9.5 / 6.5 to 9.5 Cut Type: full cut or half cut (middle left point)
  • Features: Small cylindrical package lithography processing technology excellent impact resistance, heat resistance RoHS compliant products Fully lead-free Nominal Frequency: 32.768kHz Frequency tolerance: (plusmn;5 x 10 -6 ), 10 x 10 -6 , 20 x 10 -6
  • Features: Small cylindrical package photolithographic processing technology excellent impact resistance, heat resistance RoHS compliant products Fully lead-free Nominal frequency: 32.768kHz Frequency tolerance: (plusmn;5 x 10 -6 ), 10 x 10 -6 ,plusmn;20 x 10 -6
  • Features: Compared with ordinary use of quartz crystal (load capacity 12.5pF) product, the power consumption can be reduced to the original standby 1/10. Excellent driving characteristics RoHS compliant products Nominal frequency: 32.768kHz Frequency tolerance: plusmn;20 x 10 -6 50 x 10 -6
  • Features: Compared with ordinary use of quartz crystal (load capacity 12.5pF) product, the power consumption can be reduced to the original machine during 1/10. Excellent driving characteristics RoHS compliant products Fully lead-free Nominal frequency: 32.768kHz Frequency tolerance: (plusmn;5 x 10 -6 ), 10 x 10 -6 ,plusmn;20 x 10 -6
  • 特點: 厚度為0.75mm的超薄型產品 公稱頻率:32.768kHz 頻率容許偏差: 20 x 10 -6 適用于高密度安裝的SMD型產品 優良的耐沖擊性、耐熱性 完全無鉛化內置了高信賴性、經過光刻技術加工的石英晶振 內置了高信賴性、經過光刻技術加工的石英晶振
  • Features: a thickness of 0.6mm ultra-thin products Nominal frequency: 32.768kHz Frequency tolerance: 20 x 10 -6 suitable for high density mounting SMD products excellent impact resistance, heat resistance Fully lead-free Built-in high reliability, photolithography processing technology of quartz crystal
  • Features: a thickness of 1.4mm ultra-thin products Nominal Frequency: 32.768kHz Frequency tolerance: 20 x 10-6 SMD type suitable for high-density mounting of the product Built-in high reliability, photolithography processing technology of cylindrical quartz crystal Excellent impact resistance, heat resistance RoHS compliant products
  • Features: Current detecting resistors for power supplies,motor circuits, etc. Low resistance (100 mΩ or under) and high accuracy resistors (±1 % ) for current detection. High reliability and performance with T.C.R. ±100×10 -6 /K Suitable for flow and reflow solderings. Products meet EU-RoHS requirements.
  • Features: Small and light weight. Excellent heat resistance and weather resistance, because of the use of glaze thick film as resistive film. High stability and high reliability because of the triple-layer structure of electrode. Applicable to various kinds of automatic mounters for taping, etc. Suitable for both flow and reflow solderings. Products with lead free termination meet EU-RoHS requirements. EU-RoHS regulation is not intended for Pb-glass contained in electrode, resistor element and glass. AEC-Q200 Qualified(Except 1F).
  • Features: short-term high temperature to ensure 150 ℃ 100h. Improved vibration resistance performance series on the basis of GPA, the maximum withstand vibration 392m / s2 (40G) of. most suitable for vibration, temperature demanding design, such as electric power steering system, direct injection. Rated voltage range:25~100Vdc, capacitance range: 430~5,100 μF .
  • Features: short-term high temperature to ensure 150 ℃ 100h. Improved vibration resistance performance on the basis of GPD series, the maximum withstand vibration 392m / s2 (40G) of. most suitable for vibration, temperature demanding design, such as electric power steering system,direct injection engine drive control circuit. Rated voltage range: 25~100Vdc, capacitance range: 510~8,200 μF
  • Features: to achieve a high capacity, low ESR, excellent low-temperature characteristics. Rated voltage: 25V, 35V, capacitance: 3,500 ~ 14,000 μ F Ensure 105 ℃ 5,000h. (Ripple superimposed). Ideal for automotive onboard SRS airbag device power supplies.
  • Features: High temperature & low ESR characteristics High reliability, guaranteed 125 ℃ 2,000h Rated voltage range: 2.5 ~ 10V, capacitance range: 47 ~ 470 μF Best suited for high temperature applications and other vehicular ECU.
  • Features: ESR : Less than MHJ Endurance : 2,000 hours at 125℃ Specified ESR after endurance For automobile modules and other high temperature applications Solvent resistant type (see PRECAUTIONS AND GUIDELINES) RoHS Compliant
  • Features: Superior to RK73 series in maximum working voltage. Suitable for flow and reflow solderings. Products meet EU-RoHS requirements. EU-RoHS regulation is not interded for Pb-glass contained in electrode, resistor element and glass.
  • Features: In normal condition, it works as a resistor and when exessive voltage is applied, it protects circuits by fusing quickly. The same shape as RK73 series. Recognized by safety standard UL1412. (1J is not recognized.) Suitable for both flow and reflow solderings. Products with lead free termination meet EU-RoHS requirements , EU-RoHS requlation is not intended for PB-glass contained in electrode , resistor element and glass.
  • Features: Miniature construction endurable to high voltage and high power. Resistors excellent in anti- surge characteristics. Wide resistance range of 0.5M Ω ~10G Ω and small T.C.R.. Products meet EU-RoHS requirements. EU-RoHS regulation is not intended for Pb-glass contained in resistor element and Pb contained in Brass cap.
  • Features: Resistors meeting MIL-R-26E (U and V characteristics) and surface temp. (hot spot) 350 350°C max. Resistors with a wide range of 0.1Ω~62kΩ ;, covering applications from precision to power. RW N type resistors are non-inductive wound and can be used in high frequency bands. Products meet EU-RoHS requirements. Applications: Inrush current preventitive resistors. Resistors for various power supplies such as instrumentations, communications, medical, etc. Resistors for semiconductor burn-in boards.
  • Features: Superior to RK73 series chip resistors in surge withstanding voltage and pulse withstanding voltage. SG73S (for surge) and SG73P (for pulse) are able to select resistance tolerance from 0.5%. Suitable for both reflow and flow solderings. Products with lead free termination meet EU-RoHS requirements. EU-RoHS regulation is not intended for Pb-glass contained in electrode, resistor element and glass. AEC-Q200 Qualified. Applications: E.C.U. Circuits to catch inductive lighting surge.
  • Features: Low DC resistance and high allowable current are realized by the original construction and wiring technology. Automatic surface mounting is applicable. Excellent solderability and endurance environment. Suitable for reflow soldering. Products meet EU-RoHS requirements. AEC-Q200 Qualified (LPC4045).
  • Features: Transponder coil that is arranged it s electrode in the long side of the part, and is covered with molding resin. Excellent high Q and high sensitivity, because neither the electrode nor the land pattern disturb the coil flux. Strong to vibration, shock and substrate bend test by 4 electrode terminals structure and the molded resin. Small inductance change to environmental temperature change. Suitable for reflow soldering. Products meets EU-RoHS requirements. Applications: Receiving LF anttena coil for shown below. Tire Pressure monitoring system Smart key system Immobilizer system RF-ID
  • Features: Products meet EU-RoHS requirements. CW1SS has UL1412 approval. (File No. E320246) Automatic mounting machine is applicable by surface mounted device style lead forming. Flame retardant coating(equivalent to UL94 V-0)
  • Features: Excellent anti-surge characteristics. Stable characteristics of moisture resistance up to high resistance range. RCR50 + (1MΩ ~ 12MΩ) and RCR60 (1MΩ ~ 12MΩ) are discharge resistors recognized by UL1676 and c-UL (CSA-C22.2 No.1-M94). RCR25EN (100kΩ ~ 33MΩ), RCR50EN (100kΩ ~ 33MΩ) and RCR60 (470kΩ ~ 56MΩ) is approved by EN60065 14.1 safety. Products meet EU-RoHS requirement. EU-RoHS regulation is not intended for Pb-glass contained in resistor element. Automatic mounting machine is applicable by surface mounted device style lead forming.
  • Features: KOA original ceramic resistors. Excellent in anti-pulse characteristics. High reliability agaist disconnection compared to wirewound resistors and film resistors. Products meet EU-RoHS requirements. Non-Inductive resistors. AEC-Q200 Qualified. Applications: High voltage circuits for X-ray generators and electron microscopes. Flyback transformers. Power supply circuits for machine tools, etc.
  • Features: according to the MIL-R-26E (characteristic U and V), resistive, surface temperature (hot spots) below 350 ℃ (2) Resistance range: 0.1 ~ 62K , covering everything from precision resistor to the power use RW / N is a non-inductive winding can be used in the high frequency band Application: used to prevent inrush resistor measuring measurement, communications, medical and other various power supply resistor Semiconductor screening plate resistor
  • Features: Power type current detecting resistors. Flame retardant resistors in Ceramic Case. Automatic insertion for a 5mm pitch between terminals is applicable. (26type, 58type) Low inductance. Space saving. Products meet EU-RoHS requirements.
  • Features: High-power resistor. Using frame-retardant/insulated ceramic case. Excellent in anti-pulse and inrush current. Products meet EU-RoHS requirements. EU-RoHS regulation is not intended for Pb-glass contained in glass.
  • Features: SMD platinum thin film thermal sensors for automotive. T.C.R. is equivalent to JIS IEC standards. The evaluation based on AEC-Q200 has been examined. Suitable for both flow and reflow solderings. Products meet EU-RoHS requirements. Applications: Temperature compensation of the electronic component for automotive. Temperature compensation for various kinds of sensor drive circuits. Temperature compensation for telecommunication and measuring equipment.
  • Features : Immediate cutting off against excessive current of circuit without generating heat and fuming. Excellent terminal strength and solderability due to metal electrode. Excellent dimension accuracy, mountability and shock-resistance due to plastic molding. Applicable to both reflow and flow solderings. Products with lead free termination meet EU-RoHS requirements.
  • Features: Surface mounting fuses suitable for primary and secondary circuits. Excellent mechanical strength with ceramic body. Stable fusing characteristics due to the original technology. Excellent Anti-Surge characteristics. Suitable for reflow and flow soldering. Products with lead free termination meet EU-RoHS requirements.
  • Features: Varistors own two-way symmetries and can absorb positive and negative surges. Multilayer construction allows its small size to absorb a large surge. Small space and high density mounting available due to the small package. Suitable for both flow and reflow solderings. Products with lead free termination meet EU-RoHS requirements. EU-RoHS regulation is not intended for Pb-glass contained in electrode, varistor element and glass. Applications: Protection of ESD from input and output terminals of mobile devices. Absorption of surge voltages occurred from inductive load of motors, relays, etc. Protection of semiconductor elements against over voltages. Absorption of surge voltages generated from piezoelectric elements.
  • Features: Broadside electrode chip resistor High-performance, high-reliability products T.C.R. ±100×10 -6 /K Resistance Accuracy: ± 1% withstand thermal cycling, impact and generally narrow chip resistor power rating compared to better Application: Power circuit Engine room ECU HID lamps
  • Features SMD thin film resistors with thermo-perceptivity. Various TCRs +150~+4500×10 -6 /K are available. Operating temperature range ~155°C. Rated ambient temperature: 85°C AEC-Q200 qualified. Suitable for both flow and reflow soldering. Products meet EU-RoHS reguirements. Application Temperature compensation of current sensor, FET and semiconductor. Temperature compensation for various kinds of electronic circuits and sensor.
  • Features: SMD platinum thin film thermal sensors. T.C.R. is equivalent to JIS IEC standards. Suitable for temperature control in various industrial equipment. Suitable for both flow and reflow solderings. Products meet EU-RoHS requirements. Applications Temperature compensation for various kinds of sensor drive circuits. Temperature compensation for telecommunication and measuring equipment. Temperature compensation for Hybrid ICs.
  • Features: Resistance value changes in linearly positive way to temperature. Quick response to the change of temperature. Suitable for both reflow and flow solderings. Products with lead free termination meet EU-RoHS requirements. EU-RoHS regulation is not intended for Pb-glass contained in electrode, resistor element and glass.
  • Features: LP73s are thin-film thermal sensors of SMD type. LP73s accomodate resistance tolerance 1%, wide range of TCRs,+3000× 10 -6 /K~ +5000× 10 -6 /K with the standard products. Suitable for control of temperatures in various industrial equipment. Suitable for both flow and reflow solderings. Products with lead free termination meet EU-RoHS requirements. Applications: Temperature compensation on overheat prevention for FDDs, Cameras and Small DC Motors. Temperature compensation for various kinds of Sensor Drive Circuits. Temperature compensation for Telecommunication and Measuring Devices. Temperature compensation for Hybrid ICs.
  • Features: Stable characteristics even in use for a long time with an excellent environment resistance. Products meet EU-RoHS requirements Applications: Temperature compensation of load cells for Electronic Weighing Instruments. Detections of outer air and cooling water temperatures and filter clogging of Air Conditioners. Measurement of flow rate of electronic fuel injection systems, correction of intake air temperature and oil temperature detection of Automobiles. Contact our sales representatives before you use the products for automotives. Cold point compensation and temperature detection probe of Thermocouple Temperature Controllers. Temperature compensations of various kinds of Measuring Instruments and Analyzers, Hot wires of Anemeters.
  • Features SMD thin film resistors with thermo-perceptivity. Various T.C.R.s +150 to +4500×10 -6/K are available. Suitable for both flow and reflow solderings. Products with lead free termination meet EU-RoHS requirements. Application Suitable for temperature control in various industrial equipment.
  • Features: Anti-sulfuration flat chip resistors of wide terminal type. Excellent anti-sulfuration characteristic due to using high sulfuration-proof inner top electrode material. Suitable for both flow and reflow solderings. This products meet EU-RoHS requirements.EU-RoHS regulation is not intended for Pb-glass contained in electrode, resistor element and glass. AEC-Q200 qualified. Applications: Car electronics Power supplies Industrial robots
  • Features: SMD type thick film NTC chip thermistors. Thinner (0.5mm in 1608, 2012 sizes,0.6mm in 3216 size) than the multilayer type. Excellent mountability due to its higher mechanical strength. Excellent mountability due to its solder plating at the terminal section. Suitable for both flow and reflow solderings. Products with lead free termination meet EU-RoHS requirements. EU-RoHS regulation is not intended for Pbglass contained in electrode, resistor element and glass
  • Features:SMD type of small size, ultra-low resistance (3m) and high accuracy (0.5%) resistor for current sensing.Encapsulated with flame retardant resin molding. (UL94 V0)Excellent dimension accuracy, mountability and shock-resistance due to molded products.Excellent terminal strength and solderability due to structure of a metal plate terminal electrode.Easy to absorb the thermal expansion and shrinkage because of a metal plate terminal structure.Suitable for flow, reflow and iron solderings.Products with lead free termination meet EU-RoHS requirements. EU-RoHS regulation is not intended for Pb-glass contained in electrode, resistor element and glass. AEC-Q200 Qualified.Applications:AutomotiveNote PCsBattery packsAC AdaptersDC-DC converters, etc.
  • Features: Micro Chip Fuse Rated Current: 15A breaking capacity: 24V 50A Dimensions: 3.2×1.6 Application: LCD backlight inverter DC/DC converter Battery line circuit protection
  • Features: Micro Chip Fuse Rated Current: 0.5 ~ 5A breaking capacity: 24V 50A Dimensions: 2.0×1.25x0.5mm Application: LCD backlight inverter, laptops, etc.
  • Features: Rated current: 5~20A breaking capacity: DC76V 500A Dimensions: 12.5×7.5×8.5mm Application: Communication Modules Power and other equipment
  • 特點: 保證 85℃ 2,000 小時。( 疊加紋波電流 ) 請注意不屬于基板清洗類型。
  • Features: smaller size than the KMQ series 5mm, 50% higher rated ripple current Guaranteed 105 ℃ 2000 h Rated voltage range: 160~450V, capacitance range: 100~3300 uF best suited for switching power supplies, converters use. Application: Switching Power Drive
  • Features: maximum thickness of 1.4mm thin products Suitable for high density mounting SMD type products Built-in high-reliability, after lithography processing cylindrical quartz crystal excellent impact resistance, heat resistance Application: Mobile PHS phones Handheld Computer Digital Cameras car stereo GPS Module FM tuner module Various preparatory computer clock mobile devices
  • Features: Small cylindrical package Can be widely used 32kHz ~ 200kHz low frequency bandwidth lithography processing excellent impact resistance, heat resistance RoHS compliant products Completely lead-free Application: Various transfer timing clocks, computer clocks and other uses
  • Features: Chip Fuses can be used in surface-mount type first-order and second-order circuit current in the circuit fuse using a ceramic body having excellent mechanical strength Blow stability, excellent resistance to surge resistance Application: Notebook power supply LCD Inverter Power lighting Inverter Power Copier, LBP Industrial machinery
  • Features: Ultra low resistances, suitable for large current sensing. Ultra low height with a thickness of 0.6mm, 0.25mm(TLR1E), suitable for use of small equipment. Excellent high-frequency characteristics. Filletless products.(The soldering part of this product is only a bottom electrode.) Automatic mounting machines are applicable. Suitable for reflow soldering. ( Not suitable for flow soldering . ) Products meet EU-RoHS requirements. AEC-Q200 Qualified(except 1E, 2A). Applications: Current sensing for CPU Inverter power supplies DC-DC converters Mobile device etc.
  • Features SMD metal film resistors. High precision type ±0.05% is also available as standard. High performance T.C.R. ±5×10-6/K is also available as standard. Low current noise. Suitable for control circuits in various industrial equipment. Suitable for both flow and reflow solderings. However, 1E type is available only for reflow soldering. Products with lead free termination meet EU-RoHS requirements.
  • 特征: 裝載固體電解質型感測器 類比電壓輸出,且與二氧化碳濃度成正比 高選擇性、壽命長 體積小、低功耗、低成本 應用: 空氣品質/通風控制二氧化碳濃度檢測
  • 特征: 裝載低功耗感測器TGS2610 感測器模組經過預校準,不需要用戶的專業校準工序和設備 自帶溫度補償 體積小 應用: 家用液化石油氣泄漏檢測
  • 特征: 對空氣污染氣體香煙靈敏度高 高壽命、低成本、低功耗 只需要簡單的電路設計 可探測氣體:香煙、酒精 應用: 空氣清新機控制 換氣扇控制 室內空氣質量監測
  • Feature: Lower ESR, Higher ripple current Endurance: 1000 to 5000 hours at 125 degree celsius Solvent-proof type (10 to 50V) RoHS Compliant Application: Suitable to fit for automotive equipment
  • Feature: Rate Voltage Range Vdc : 6.3 to 100 Capacitance Range uF : 560 to 820,000 uF Endurance with ripple current : 2,000 hours at 105 degree celsius Non solvent-proof type RoHS Compliant Application: General Purpose
  • 特征: 外殼的17毫米,厚度5毫米的超小型薄型風扇 馬達部緊湊,理想的盒子形狀/翅膀形狀 實現高風量、低噪音 額定電壓,轉數更快高風量類型也對應 FG 信號,STOP信號輸出也對應 應用: 越小型化的映射設備 通訊機器
  • Feature: Lead-free Soldering, Cadmium-free Resistance tolerance ± 10% "O" ring sealed and washable Suitable for automatic insertion and automatic adjustment Increase in the level of characteristics in the high frequency field (In House Comparison) Application: General Purpose
  • FEATURES RoHS compliant Low profile of 3.0 mm Wide variety (top or side setting, 10 or 16 positions, J-hook, gull wing or through hole pins) to choose from Easy to recognize Low-profile side setting type with support terminals is available
  • 特征: 表壓: 0~4.90 , ~686KPa 用于氣體 額定輸出: 100 30mV 電源: 1.5mADC 應用: 測量設備 醫療設備和分析儀 工業設備 半導體設備
  • FEATURES RoHS compliant Fine click with metallic spring Low profile of 3.9 mm makes perfect for high density board mounting applications Gold plated contact provides excellent reliability Cross and minus slot are available Terminal pin arrangement 4-1
  • FEATURES RoHS compliant Fine click with metallic spring Low profile of 3.9 mm makes perfect for high density board mounting applications Gold plated contact provides excellent reliability Cross and minus slot are available Terminal pin arrangement
  • FEATURES High reliability by Gold contact RoHS compliant Available to detect from Top or side direction Automatic mounting possible Ultra-compact Low profile design of 3.35mm APPLICATIONS Detection of Communication devices,Audio-visual equipment, Industrial instrument,Security devices, etc.
  • Feature: It with low noises,the price is cheaper than FPA 630V Series,and smaller. Application: LED,TV,POWER
  • 特點: 跟片狀電阻(RK73)相比,它的耐浪涌電壓和脈沖電壓都非常好 SG73S(用于浪涌)和SG73P(用于脈沖)都可選擇 ± 0.5%的電阻值容許差 應用: E.C.U 感應電閃電路
  • Feature: SMD type metal oxide varistors Ideal for the countermeasure against ESD (Conforming to IEC6100-4-2) Symmetrical non-linearity V-I characteristics absorb positive and negative surge High maximum energy type Operating temperatures up to 125 degree celsius Application: Protection from surge to electronic device for automotive Protection of ESD from input and output terminals of mobile phones Absorption of surge voltages occurred from inductive load of motors, relays, etc. Protection of semiconductor elements against over voltages
  • Applications Rotary and linear encoders Magnetic or optical sin/cos sensor interface Brushless motor commutation (2...64 poles) Imbedded motion control Features Differential PGA inputs for sine, cosine, and index Input frequency of up to 700 kHz AB output frequency of up to 12.5 MHz Automatic compensation of amplitude, offset, and phase errors Low latency (typ. 1.5 μs) Differential RS422 line driver outputs for ABZ or UVW Simultaneous single-ended outputs for ABZ and UVW Digital filtering for ultra-low output jitter Complete status and fault monitoring capabilities Configured by pins or SPI In-field re-configuration via Encoder Link interface Easy to use with built-in line driver, EEPROM, and oscillator Push-button automatic calibration for fast commissioning LED intensity control by PWM output 10-bit angle data and 14-bit multi-cycle counter available to SPI Capture register for coded reference marks and touch-probe applications Space-saving 5 x 5mm QFN package Single 3.3 V supply

  • Applications Incremental encodersMiniature motors and actuatorsX-Y and linear stagesFactory automation robotsConsumer robots Features Lensless, reflective opto-encoder iCs, compact, high-resolution, incrementalSuitable reflective code discs of 4, 14, 26 and 43mm and linear scales with 256 μm period lengthMonolithic HD Phased Array with excellent signal matchingIntegrated blue LED with power control, EncoderBlueLow-noise signal amplifiers with high EMI tolerancePin-selectable modes of operation:Digital A/B/Z (x1, x2, x4, x8, x16 interpolated), analog COS/SIN with analog or digital ZPin-selectable index gating:Ungated (1 T), B-gated (0.5 T), AB-gated (0.25 T)Pin-selectable minimal edge distance: 80 ns, 1 μs, 10 μsComplementary quadrature outputs PA, NA,PB and NBComplementary index outputs PZ and NZAnalog signal output for ease of alignment and resolution enhancement by external interpolationOperating temperature range of -40 °C to +105 °CCompact and lensless optoQFN mold packageEvaluation kits on request

  • Applications Digital angular sensor technology, 0--360 ° Incremental angular encoder Absolute angular encoder Brushless motors Motor feedback Rotational speed control Features Real-time system for full resolution at up to 200 000 rpm Integrated Hall sensors with automatic offset compensation 4x sensor arrangement for fault-tolerant adjustment Amplitude control for optimum operating point FlexCount interpolator with 1 to 1024 CPR, resolution up to 4 096 / 0.08 ° UVW commutation signals with 1 to 16 CPR, for motors of up to 16 pole pairs Programmable resolution, hysteresis, edge spacing, zero position and rotating direction Up to 16 MHz incremental edge rate RS422-compatible AB encoder signals with index Z BiSS/SSI interface for data output and configuration Integrated Zapping ROM for default setup and OEM data Errors signalized via pin and serial interface Single 5 V supply with reversed-polarity monitoring and sub-system switching Extended temperature range from -40 to +125 °C

  • Off-Axis Motor Feedback Module Applications Rotary encoder Motor feedback Motion control Features Magnetic off-axis absolute position encoder module 17-Bit position data output via fast serial interfaces BiSS/SSI Quadrature ABZ signals via RS-422 line driver iC-HF or Sin/Cos outputs via line driver iC-MSA Programmable resolution of 1 to 32,768 CPR (FlexCount) Position preset function Rotational speed to 12,000 RPM 5 V power supply with reverse polarity protection Operational temperature range of -40 °C to 85 °C Ready to operate eval kit incl. magnetic disc MU2S 30-32N and cables Configuration GUI software with automatic calibration functions available

  • 特點: 廣泛和靈活的產品平臺 采用無焊接SPRiNG彈簧連接技術,讓裝配時間縮至最短 無銅底板,具成本效益 采用最新的600V、1200V、1700V芯片技術 電流范圍4A到400A,逆變器功率可達90kW 全面的拓撲結構:CIB(整流逆變制動),三相全橋,雙三相全橋,H橋,半橋,三電平,不受控制/半控橋整流器與制動斬波器,客戶自定的電路拓撲結構 應用: 主要應用包括各種逆變器,如標準驅動器、獨立驅動器、伺服驅動器、系統驅動器、太陽能逆變器,UPS系統和焊機。

  • 特點: 電壓等級分為600V,1200V和1700V,電流范圍75到600A 直接驅動組件 采用彈簧或press-fit連接,最高耐用性 半橋、三相全橋和斬波器拓撲結構 多個IGBT 來源 集成電流傳感分流電阻器 應用: SEMiX是一款靈活和面向應用的模塊。基于可擴展的平臺概念,現代芯片技術集成入IGBT和整流器模塊,適用于各類應用,例如交流電機驅動,開關電源和電流源逆變器。其他典型應用包括不間斷電源、光伏系統和風能。

  • 特點: 拓撲結構:半橋、斬波器、單開關、MLI、共發射極 以Al2O3絕緣的銅底板使用DCB技術(直接銅綁定) UL認證 應用: 成熟的封裝設計可用于各類應用,例如用于可再生能源的逆變器和電源。長久的使用壽命完美切合了技術要求較高的應用,例如交流驅動,開關磁阻和直流電機。

  • 特點: 800V到2200V 15A到1200A 不可控,半控和可控整流器 單晶閘管和二極管 應用: 晶閘管,晶閘管/二極管或二極管模塊的目標應用包括用于逆變器或者UPS系統,軟啟動應用和控制系統輸入整流器(單相,三相,不可控,半控或可控)

91超碰国产在线观看